https://kd85.com/liantec.html

For information about the Bytemine appliances, check http://bytemine.kd85.com/

LPC-5740E1N4-512

Power consumption is 18 Watts, 20 Watts under load with one ethernet port active.

When compiling, the temperature rises from 55 degrees to 66 degrees, but so far it never went above that.

For each ethernet port you plug in, power consumption jumps with about 3 Watts. In total the machine has never consumed more than 30 Watts which is still fine to work reliable as fanless. The touch of the case is hot but never up to a point where the machine becomes unreliable. I would not stack another machine or phonebook on top of it though ;)

The CF slot is located on the bottom of the board, which is kind of unfortunate as you need to unscrew the board to access it ;-(

OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: VIA Eden Processor 1000MHz ("CentaurHauls" 686-class) 1 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,SSE3,EST,TM2,xTPR
cpu0: RNG AES AES-CTR SHA1 SHA256 RSA
real mem  = 468152320 (446MB)
avail mem = 444497920 (423MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 02/25/08, BIOS32 rev. 0 @ 0xfa0e0, SMBIOS rev. 2.3 @ 0xf0000 (34 entries)
bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 02/25/2008
bios0: VIA Technologies, Inc. CX700
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xce14
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfcce0/288 (16 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 17 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 5 7 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xf000 0xd0000/0x1000
cpu0 at mainbus0
cpu0: unknown Enhanced SpeedStep CPU, msr 0x04090a0904000a09
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 1333 MHz (844 mV): speeds: 1333, 533 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA CX700 Host" rev 0x10
agp0 at pchb0: v3, aperture at 0xd0000000, size 0x10000000
pchb1 at pci0 dev 0 function 1 "VIA CX700 Host" rev 0x00
pchb2 at pci0 dev 0 function 2 "VIA CX700 Host" rev 0x00
pchb3 at pci0 dev 0 function 3 "VIA CX700 Host" rev 0x00
pchb4 at pci0 dev 0 function 4 "VIA CX700 Host" rev 0x00
pchb5 at pci0 dev 0 function 7 "VIA CX700 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA S3 UniChrome Pro II IGP" rev 0x03
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pciide0 at pci0 dev 15 function 0 "VIA CX700 IDE" rev 0x00: ATA133, channel 0 configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 disabled (no drives)
wd0 at pciide0 channel 1 drive 1: 
wd0: 1-sector PIO, LBA, 2001MB, 4098528 sectors
wd0(pciide0:1:1): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x90: irq 10
uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0x90: irq 5
uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0x90: irq 7
ehci0 at pci0 dev 16 function 4 "VIA VT6202 USB" rev 0x90: irq 11
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1
viapm0 at pci0 dev 17 function 0 "VIA CX700 ISA" rev 0x00
iic0 at viapm0
pchb6 at pci0 dev 17 function 7 "VIA VX700 Host" rev 0x00
pchb7 at pci0 dev 19 function 0 "VIA CX700 Host" rev 0x00
ppb1 at pci0 dev 19 function 1 "VIA CX700 PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
em0 at pci2 dev 6 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: irq 7, address 00:06:93:f0:7e:09
em1 at pci2 dev 7 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: irq 5, address 00:06:93:f0:7e:0a
em2 at pci2 dev 8 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: irq 10, address 00:06:93:f0:7e:0b
em3 at pci2 dev 9 function 0 "Intel PRO/1000MT (82541GI)" rev 0x05: irq 11, address 00:06:93:f0:7e:0c
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "VIA UHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: 
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: W83697HF rev 0x12
lm1 at wbsio0 port 0x290/8: W83697HF
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask ffe5 netmask ffe5 ttymask ffe7
uhub4 at uhub2 port 2 "Mitsumi Electric Hub in Apple Extended USB Keyboard" rev 1.10/3.95 addr 2
uhidev0 at uhub4 port 3 configuration 1 interface 0 "Mitsumi Electric Apple Extended USB Keyboard" rev 1.10/3.95 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 13
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 3 configuration 1 interface 1 "Mitsumi Electric Apple Extended USB Keyboard" rev 1.10/3.95 addr 3
uhidev1: iclass 3/0, 3 report ids
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b

# sysctl hw                                                                    
hw.machine=i386
hw.model=VIA Eden Processor 1000MHz ("CentaurHauls" 686-class)
hw.ncpu=1
hw.byteorder=1234
hw.pagesize=4096
hw.disknames=wd0,sd0
hw.diskcount=2
hw.sensors.lm1.temp0=59.00 degC
hw.sensors.lm1.temp1=65.50 degC
hw.sensors.lm1.volt0=0.83 VDC (VCore)
hw.sensors.lm1.volt1=3.23 VDC (+3.3V)
hw.sensors.lm1.volt2=4.87 VDC (+5V)
hw.sensors.lm1.volt3=11.67 VDC (+12V)
hw.sensors.lm1.volt4=5.16 VDC (-12V)
hw.sensors.lm1.volt5=5.11 VDC (-5V)
hw.sensors.lm1.volt6=4.82 VDC (5VSB)
hw.sensors.lm1.volt7=3.22 VDC (VBAT)
hw.cpuspeed=1333
hw.setperf=100
hw.vendor=VIA Technologies, Inc.
hw.product=CX700
hw.uuid=Not Set
hw.physmem=468152320
hw.usermem=468148224